low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 1 / 9 version 6.3 product features applications ? gaas p-hemt chip on board ? no matching circuit needed ? high maximum input power(+25dbm) ? high ip3 & low noise ? single supply voltage (+5v) ? surface mount hybrid type ? tape & reel packaging ? small size, high heatsink ? alumina substrate ? pb free / rohs standard ? 2g & 3g repeater ? base station ? pcs, cdma, w-cdma ? gsm, dcs, umts ? wimax, wibro, wlan ? rf sub-systems description rfhic?s low noise amplifier series are all hybrid lna type produc ts which includes all matching for the convenience of customer s. cl series are focused on giving lowest noise possible. the struct ure of the device is built with gaas p-hemt die attached on a ceramic thick film substrate. the device is still smaller than the area one would use for the application notes all together. d epending on the part number, one can use this in different frequency applications. all lna hybrids are possible to have custom frequency & spec without any additional nre cost involved. all rfhic products are rohs compliant. electrical specifications parameter unit cl0901-l cl1501-l cl1801-l cl2101-l frequency range mhz 824 ~ 894 (cellular) 890 ~ 960 (gsm) 1400 ~ 1600 1700 ~ 2000 1850 ~ 2200 small signal gain (s 21 ) db 19 18 16 15.5 14 gain flatness db 0.5 0.5 0.5 0.5 1.0 input return loss (s 11 ) db -18 -18 -18 -18 -18 output return loss (s 22 ) db -10 -10 -10 -10 -10 1db compression point (p 1 db) dbm 14 14 15 16 16 output 3 rd order intercept point (oip3) (typ.) dbm 27 27 27 27 27 noise figure (typ.) db 0.5 0.5 0.7 0.6 0.7 dc supply current (vdc=+5v) ma 65 65 45 45 45 test condition supply voltage = +5v, 50ohm system, ta = 25 oip3 is measured with two tones, at an output power of +0dbm/tone separated by 1mhz. package type : cp-16a
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 2 / 9 version 6.3 absolute maximum ratings parameter unit rating remark device voltage v 8 - rf input power dbm 25 - operating temperature -40 ~ 85 - storage temperature -50 ~ 125 - note operation of this device in excess of any one of these parameters may cause permanent damage. functional diagram application circui t esd protection gallium arsenide integrated circuits are sensitive to electrostat ic discharge (esd) and can be damaged by static electricity. p roper esd control techniques should be used when handling these devices. some of the precautions recommended are; - person at a workbench should be earthed via a wrist strap and a resistor. - all mains-powered equipment should be connected to the mains via an earth-leakage switch. - equipment cases should be grounded. - relative humidity should be ma intained between 40% and 50%. - an ionizer is recommended. - keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench.
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 3 / 9 version 6.3 cl0901-l (cellular) s-parameter oip3 noise figure p1db
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 4 / 9 version 6.3 cl0901-l (gsm) s-parameter oip3 noise figure p1db
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 5 / 9 version 6.3 cl1801-l (pcs) s-parameter oip3 noise figure p1db
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 6 / 9 version 6.3 cl2101-l (imt2000) s-parameter oip3 noise figure p1db
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 7 / 9 version 6.3
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 8 / 9 version 6.3 package dimensions (type: cp-16a) * unit: mm[inch] | tolerance 0.15[.006] top view side view bottom view pin description pin no function pin no function 1 gnd 4 gnd 2 input 5 output 3 gnd 6 vcc recommended pattern recommended mounting configuration * mounting configuration notes 1. ground / thermal via holes are critical for the proper performance of this device. 2. add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. mounting screws can be added near the part to fasten the board to a heatsink. ensure that the ground / thermal via hole regi on contacts the heatsink. 4. do not put solder mask on the backside of the pcb in the region where the board contacts the heatsink. 5. rf trace width depends upon the pcb material and construction. 6. use 1 oz. copper minimum.
low noise amplifier cl0901-l / cl1501-l cl1801-l / cl2101-l k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 9 / 9 version 6.3 revision history part number release date version modification data sheet status cl0901-l cl1501-l cl1801-l cl2101-l 2012.10.19 6.3 new datasheet format - cl0901-l cl1501-l cl1801-l cl2101-l 2012.2.18 6.2 - - rfhic corporation reserves the right to make changes to any prod ucts herein or to discontinue any product at any time without n otice. while product specifications have been thoroughly examined for reliability, rfhic corporation strongly recommends buy ers to verify that the information they are using is accurat e before ordering. rfhic corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including wi thout limitation consequential or incidental damages. rfhic products are not intended for use in life support equipment or application where malfunction of the product can be expect ed to result in personal injury or death. buyer uses or sells such products for any such unintended or unauthorized application, buyer shall i ndemnify, protect and hold rfhic corporat ion and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. sales, inquiries and support should be directed to the local au thorized geographic distributor for rfhic corporation. for custo mers in the us, please contact the us sales team at 919- 677-8780. for all other inquiries, please contact the international sales team at 82-31-250-5078.
|
